BootROM 1.15 Booting from NOR flash DDR3 Training Sequence - Ver 2.5.BootROM: Image checksum verification PASSED ** LOADER ** U-Boot 2009.08 (Jul 27 2012 - 18:23:11) Plat'Home version: 1.1.1 (Base: Marvell BSP 2.2.3 NQ) U-Boot Addressing: Code: 00600000:006BFFF0 BSS: 0070D6A0 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 Board: OpenBlocks AX3 SoC: MV78260 A0 running 2 CPUs Custom configuration CPU: Marvell PJ4B (584) v7 (Rev 2) LE CPU # 0 CPU @ 1333Mhz, L2 @ 667Mhz DDR @ 667Mhz, TClock @ 250Mhz DDR 64Bit Width, FastPath Memory Access DDR ECC Disabled PEX 0.0(0): Detected No Link. PEX 0.1(1): Detected No Link. DRAM: 1 GB CS 0: base 0x00000000 size 1 GB Addresses 14M - 0M are saved for the U-Boot usage. Flash: 128 MB POST: mac verify Eth0 PASSED Eth1 PASSED Eth2 PASSED Eth3 PASSED FPU initialized to Run Fast Mode. USB 0: Host Mode USB 1: Host Mode USB 2: Device Mode Power Off External Interface Modules Detected: MMC: MRVL_MMC: 0 Net: egiga0, egiga1, egiga2, egiga3 Hit any key to stop autoboot: 0 Run Boot Selection Script *** SW 2 IS OFF *** *** SW 3 IS OFF, Standard Boot *** Bootargs: root=/dev/ram rootdelay=0 vmalloc=145M mtdparts=cfi_flash_0:0xe0000(uboot)ro,0x40000(env),0x20000(tstprg)ro,0x600000(config),0x2800000(linux),0x30c0000(user),0x2000000(opt) console=ttyS0,115200 ## Booting kernel from Legacy Image at 02000000 ... Image Name: OBSAX3 3.0.6-3 Created: 2012-07-27 10:27:15 UTC Image Type: ARM Linux Multi-File Image (gzip compressed) Data Size: 31996931 Bytes = 30.5 MB Load Address: 00008000 Entry Point: 00008000 Contents: Image 0: 1993890 Bytes = 1.9 MB Image 1: 30003027 Bytes = 28.6 MB Verifying Checksum ... OK ## Loading init Ramdisk from multi component Legacy Image at 02000000 ... Uncompressing Multi-File Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Initializing cgroup subsys cpu Linux version 3.0.6 (root@squeeze) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Jul 27 19:25:24 JST 2012 CPU: Marvell - PJ4Bv7 Processor [562f5842] revision 2 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Marvell Armada XP Development Board Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writealloc SMP: init cpus PERCPU: Embedded 7 pages/cpu @c0d84000 s7200 r8192 d13280 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 Kernel command line: root=/dev/ram rootdelay=0 vmalloc=145M mtdparts=cfi_flash_0:0xe0000(uboot)ro,0x40000(env),0x20000(tstprg)ro,0x600000(config),0x2800000(linux),0x30c0000(user),0x2000000(opt) console=ttyS0,115200 PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1024MB = 1024MB total Memory: 1004580k/1004580k available, 43996k reserved, 238592K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xf1800000 - 0xfa800000 ( 144 MB) lowmem : 0xc0000000 - 0xf1700000 ( 791 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .init : 0xc0008000 - 0xc0034000 ( 176 kB) .text : 0xc0034000 - 0xc0512000 (4984 kB) .data : 0xc0512000 - 0xc053b7c0 ( 166 kB) .bss : 0xc053b7e4 - 0xc057d550 ( 264 kB) Hierarchical RCU implementation. NR_IRQS:211 Initializing ArmadaXP SOC Timer 0 sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms Console: colour dummy device 80x30 Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok SMP: prepare CPUs (2 cores) SMP: CPU 0 Waking up CPU 1 Armada-XP Performance Monitor Unit detected (Marvell ID)!!! hw perfevents: enabled with Armada PJ4 PMU driver, 7 counters available CPU1: Booted secondary processor Brought up 2 CPUs SMP: Total of 2 processors activated (2664.03 BogoMIPS). devtmpfs: initialized NET: Registered protocol family 16 Aurora: Working in ARMv7 mode L0 cache Enabled Speculative Prefetch Disabled Aurora L2 Cache Enabled Support IO coherency. Marvell Armada-XP DB-78460-BP rev 2.0 Board - Soc: MV78260 A0 LE Detected Tclk 250000000, SysClk 667000000, FabricClk 667000000, PClk 1333000000 LSP version: AXP_2.0.6 registered dev#0 asa ehci_marvell Marvell USB EHCI Host controller #0: f10af6c0 registered dev#1 asa ehci_marvell Marvell USB EHCI Host controller #1: f10af5c0 Warning Integrated USB 2 is Powered Off PCI-E: Cheking physical bus #0 (controller #0): Enabled - No Link PCI-E: Cheking physical bus #1 (controller #1): Enabled - No Link PCI-E: Cheking physical bus #2 (controller #8): Disabled bio: create slab at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource axp_clocksource cfg80211: Calling CRDA to update world regulatory domain Switched to NOHz mode on CPU #0 Switched to NOHz mode on CPU #1 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 29300K PMU: registered new PMU device of type 0 Armada XP hwmon thermal sensor initialized. ArmadaXP Power Managament Suspend Operations Initialized Initializing Armada-XP CPU power management (WFI) audit: initializing netlink socket (disabled) type=2000 audit(0.510:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Registering unionfs 2.5.11 (for 3.0.18) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). msgmni has been set to 1553 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) mv_xor mv_xor.2: Marvell XOR: ( xor cpy ) mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy ) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xd0012000 (irq = 41) is a 16550A console [ttyS0] enabled serial8250.1: ttyS1 at MMIO 0xd0012100 (irq = 42) is a 16550A OpenBlockS Family LED driver v0.2 Push switch driver v0.1 brd: module loaded loop: module loaded sata_mv sata_mv.0: version 1.28 sata_mv sata_mv.0: cannot get clkdev sata_mv sata_mv.0: slots 32 ports 2 scsi0 : sata_mv scsi1 : sata_mv ata1: SATA max UDMA/133 irq 55 ata2: SATA max UDMA/133 irq 55 INFO: Found cfi_flash_0 0 - base 0xe8000000, size 0x8000000, bus 2 INFO: Found spi_flash 0 - base 0xf0000000, size 0x100000 INFO: flashInfoFill - Found 2 Flash Devices INFO: flash_map_init - detected 2 devices MTD: Initialize the cfi_flash_0 device at address 0xe8000000 INFO: Io remapped successfully - phy addr = 0xe8000000, virt addr = 0xf2000000 INFO: Using cfi_probe to probe cfi_flash_0 at address 0xe8000000, size 0x8000000, width 2m cfi_flash_0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x00227e Amd/Fujitsu Extended Query Table at 0x0040 Amd/Fujitsu Extended Query version 1.3. number of CFI chips: 1 - detected OK 7 cmdlinepart partitions found on MTD device cfi_flash_0 Creating 7 MTD partitions on "cfi_flash_0": 0x000000000000-0x0000000e0000 : "uboot" 0x0000000e0000-0x000000120000 : "env" 0x000000120000-0x000000140000 : "tstprg" 0x000000140000-0x000000740000 : "config" 0x000000740000-0x000002f40000 : "linux" 0x000002f40000-0x000006000000 : "user" 0x000006000000-0x000008000000 : "opt" - OK. MTD: Initialize the spi_flash device at address 0xf0000000 INFO: Io remapped successfully - phy addr = 0xf0000000, virt addr = 0xf1a00000 INFO: Using sflash to probe spi_flash at address 0xf0000000, size 0x100000, width 2m - Not detected - FAILED! mv_eth_probe: port_mask=0xf, cpu_mask=0x3 0 - Base 0x00000000 , Size = 0x40000000. 4 - Base 0xf4000000 , Size = 0x00100000. 8 - Base 0xe0000000 , Size = 0x02000000. 10 - Base 0xe2000000 , Size = 0x02000000. 12 - Base 0xe4000000 , Size = 0x02000000. 14 - Base 0xe6000000 , Size = 0x02000000. 28 - Base 0xd0000000 , Size = 0x00100000. 30 - Base 0xf0000000 , Size = 0x00100000. 38 - Base 0xfff00000 , Size = 0x00100000. 39 - Base 0xe8000000 , Size = 0x08000000. 41 - Base 0xc8010000 , Size = 0x00010000. 42 - Base 0xf4480000 , Size = 0x00010000. 43 - Base 0xf4500000 , Size = 0x00100000. mvPncVirtBase = 0xf1e00000 o 4 Giga ports supported o SKB recycle supported (Enabled) o NETA acceleration mode 4 o BM supported for CPU: 4 BM pools o PnC supported (Enabled) o HWF supported o RX Queue support: 8 Queues * 128 Descriptors o TX Queue support: 8 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Loading network interface(s) o Port 0 is connected to Linux netdevice giga p=0: mtu=1500, mac=f102fe58 o eth0, ifindex = 2, GbE port = 0 o Port 1 is connected to Linux netdevice giga p=1: mtu=1500, mac=f102fe58 o eth1, ifindex = 3, GbE port = 1 o Port 2 is connected to Linux netdevice giga p=2: mtu=1500, mac=f102fe58 o eth2, ifindex = 4, GbE port = 2 o Port 3 is connected to Linux netdevice giga p=3: mtu=1500, mac=f102fe58 o eth3, ifindex = 5, GbE port = 3 sky2: driver version 1.28 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.0: Marvell Orion EHCI ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100 ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: Marvell Orion EHCI usb usb1: Manufacturer: Linux 3.0.6 ehci_hcd usb usb1: SerialNumber: ehci_marvell.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_marvell ehci_marvell.1: Marvell Orion EHCI ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 2 ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100 ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: Marvell Orion EHCI usb usb2: Manufacturer: Linux 3.0.6 ehci_hcd usb usb2: SerialNumber: ehci_marvell.1 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver rtc-s35390a 1-0030: rtc core: registered rtc-s35390a as rtc0 cpuidle: using governor ladder cpuidle: using governor menu oprofile: using arm/mrvl_pj4b nf_conntrack version 0.5.0 (16154 buckets, 64616 max) VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 registered taskstats version 1 rtc-s35390a 1-0030: setting system clock to 2012-09-22 14:57:28 UTC (1348325848) aa1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata1.00: ATA-8: MRSAJ5A016GC118C00, MRV1.1.3, max UDMA/133 ata1.00: 29323728 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA MRSAJ5A016GC118C MRV1 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 29323728 512-byte logical blocks: (15.0 GB/13.9 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sd 0:0:0:0: [sda] Attached SCSI disk ata2: SATA link down (SStatus 0 SControl F300) RAMDISK: lzma image found at block 0 VFS: Mounted root (ext2 filesystem) on device 1:0. [prepare_namespace] Executing flashcfg... NET: Registered protocol family 1 [prepare_namespace] Finished executing flashcfg Freeing init memory: 176K INIT: version 2.88 booting Setting the system clock. fsck from util-linux-ng 2.17.2 DEBIAN: clean, 17036/917504 files, 185370/3664828 blocks EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...done. Activating swap...done. Checking root file system...fsck from util-linux-ng 2.17.2 /dev/ram0: clean, 8769/32768 files, 102751/131072 blocks done. Cleaning up ifupdown.... Loading kernel modules...done. Activating lvm and md swap...done. Checking file systems...fsck from util-linux-ng 2.17.2 done. Setting up networking.... Mounting local filesystems...done. Activating swapfile swap...done. Cleaning up temporary files.... Configuring network interfaces...pool #0: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added eth0: started pool #1: pkt_size=1536, buf_size=1632 - 2048 of 2048 buffers added eth1: started done. Setting kernel variables ...done. Starting portmap daemon...Already running.. Starting NFS common utilities: statd failed! Cleaning up temporary files.... INIT: Entering runlevel: 2 Starting portmap daemon.... Starting NFS common utilities: statd. Starting enhanced syslogd: rsyslogd. Starting deferred execution scheduler: atd. Starting periodic command scheduler: cron. Starting MTA: exim4. Starting OpenBSD Secure Shell server: sshdsshd (1408): /proc/1408/oom_adj is deprecated, please use /proc/1408/oom_score_adj instead. . Debian GNU/Linux 6.0 obsax3 ttyS0 obsax3 login: