BusyBox v1.28.3 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 18.06.0, r7188-b0b5c64c22 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:~# root@OpenWrt:~# cat /proc/cpuinfo system type : MediaTek MT7620N ver:2 eco:6 machine : ELECOM WRH-300CR processor : 0 cpu model : MIPS 24KEc V5.0 BogoMIPS : 385.84 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] isa : mips1 mips2 mips32r1 mips32r2 ASEs implemented : mips16 dsp shadow register sets : 1 kscratch registers : 0 package : 0 core : 0 VCED exceptions : not available VCEI exceptions : not available root@OpenWrt:~# root@OpenWrt:~# dmesg [ 0.000000] Linux version 4.14.54 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9)) #0 Mon Jul 30 16:25:17 2018 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is ELECOM WRH-300CR [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80416f80, node_mem_map 81000040 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] random: get_random_bytes called from 0x8041a72c with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0001f9e8 [ 0.000000] Readback ErrCtl register=0001f9e8 [ 0.000000] Memory: 60308K/65536K available (3552K kernel code, 179K rwdata, 460K rodata, 152K init, 222K bss, 5228K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015475] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.087708] pid_max: default: 32768 minimum: 301 [ 0.097131] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.110156] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.129028] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.148508] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.160681] pinctrl core: initialized pinctrl subsystem [ 0.172214] NET: Registered protocol family 16 [ 0.185784] Can't analyze schedule() prologue at 80373d10 [ 0.211685] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.222716] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.235302] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.246292] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.258859] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.269846] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.282451] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.293266] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.310080] clocksource: Switched to clocksource systick [ 0.321738] NET: Registered protocol family 2 [ 0.331311] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.345090] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.357676] TCP: Hash tables configured (established 1024 bind 1024) [ 0.370443] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.381950] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.394662] NET: Registered protocol family 1 [ 0.403234] PCI: CLS 0 bytes, default 32 [ 0.405564] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.418253] Crashlog allocated RAM at address 0x3f00000 [ 0.429960] workingset: timestamp_bits=30 max_order=14 bucket_order=0 [ 0.448528] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.460025] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.488102] io scheduler noop registered [ 0.495802] io scheduler deadline registered (default) [ 0.506894] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.522461] console [ttyS0] disabled [ 0.529455] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.549224] console [ttyS0] enabled [ 0.562998] bootconsole [early0] disabled [ 0.579552] cacheinfo: Failed to find cpu0 device node [ 0.589826] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.608282] spi spi0.0: force spi mode3 [ 0.616756] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.626926] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.639587] Creating 5 MTD partitions on "spi0.0": [ 0.649148] 0x000000000000-0x000000030000 : "u-boot" [ 0.659951] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.671434] 0x000000040000-0x000000050000 : "factory" [ 0.682435] 0x000000050000-0x000000210000 : "recover" [ 0.693402] 0x000000210000-0x000001000000 : "firmware" [ 0.812987] 2 uimage-fw partitions found on MTD device firmware [ 0.824822] 0x000000210000-0x00000036c64e : "kernel" [ 0.835619] 0x00000036c64e-0x000001000000 : "rootfs" [ 0.846386] mtd: device 6 (rootfs) set to be root filesystem [ 0.859027] 1 squashfs-split partitions found on MTD device rootfs [ 0.871412] 0x0000005d0000-0x000001000000 : "rootfs_data" [ 0.883813] libphy: Fixed MDIO Bus: probed [ 0.896319] gsw: setting port4 to ephy mode [ 0.904732] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 4 link up (100Mbps/Full duplex) [ 0.923163] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.935666] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.952678] rt2880_wdt 10000120.watchdog: Initialized [ 0.964175] NET: Registered protocol family 10 [ 0.976769] Segment Routing with IPv6 [ 0.984255] NET: Registered protocol family 17 [ 0.993194] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.019025] 8021q: 802.1Q VLAN Support v1.8 [ 1.042919] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.057829] Freeing unused kernel memory: 152K [ 1.066702] This architecture does not have kernel memory protection. [ 2.613845] init: Console is alive [ 2.620943] init: - watchdog - [ 2.670039] random: fast init done [ 4.416047] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.685322] usbcore: registered new interface driver usbfs [ 4.696403] usbcore: registered new interface driver hub [ 4.707117] usbcore: registered new device driver usb [ 4.722644] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.737318] ehci-platform: EHCI generic platform driver [ 4.758125] phy phy-usbphy.0: remote usb device wakeup disabled [ 4.769933] phy phy-usbphy.0: UTMI 16bit 30MHz [ 4.778806] ehci-platform 101c0000.ehci: EHCI Host Controller [ 4.790306] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 4.806205] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 4.826042] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 4.839510] hub 1-0:1.0: USB hub found [ 4.847392] hub 1-0:1.0: 1 port detected [ 4.858422] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.872324] ohci-platform: OHCI generic platform driver [ 4.883108] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 4.896718] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 4.912594] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.950715] hub 2-0:1.0: USB hub found [ 4.958643] hub 2-0:1.0: 1 port detected [ 4.970550] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.989074] init: - preinit - [ 5.939926] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 6.397109] hub 1-1:1.0: USB hub found [ 6.412407] hub 1-1:1.0: 4 ports detected [ 6.493660] random: procd: uninitialized urandom read (4 bytes read) [ 6.886068] 8021q: adding VLAN 0 to HW filter on device eth0 [ 6.929465] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 8.019022] jffs2: notice: (394) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found. [ 8.052576] mount_root: switching to jffs2 overlay [ 8.094371] overlayfs: upper fs does not support tmpfile. [ 8.115210] urandom-seed: Seeding with /etc/urandom.seed [ 8.266315] procd: - early - [ 8.272157] procd: - watchdog - [ 8.752454] procd: - watchdog - [ 8.759011] procd: - ubus - [ 8.987684] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.178133] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.191396] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.205183] procd: - init - [ 9.604803] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.624077] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.739896] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180 [ 9.755910] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d [ 9.773430] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.793425] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 9.871280] xt_time: kernel timezone is -0000 [ 9.945960] PPP generic driver version 2.4.2 [ 9.957316] NET: Registered protocol family 24 [ 9.996392] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory" [ 10.010872] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 10.026337] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 10.040735] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 10.145440] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.521209] urandom_read: 5 callbacks suppressed [ 11.521219] random: jshn: uninitialized urandom read (4 bytes read) [ 20.810897] 8021q: adding VLAN 0 to HW filter on device eth0 [ 20.849995] br-lan: port 1(eth0) entered blocking state [ 20.860475] br-lan: port 1(eth0) entered disabled state [ 20.871275] device eth0 entered promiscuous mode [ 20.976498] br-lan: port 1(eth0) entered blocking state [ 20.986975] br-lan: port 1(eth0) entered forwarding state [ 20.997943] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 21.923248] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready