The system is coming up, please wait... Read board ID of 0x80 from addr 0x23 Read extended model ID of 0x19 from addr 0x22 Matched board/model ID to platform index 6 Read board ID of 0x80 from addr 0x23 Read extended model ID of 0x19 from addr 0x22 Matched board/model ID to platform index 6 Checking system RAM - press any key to stop test Checking memory address: 00100000 System RAM test using Default POST RAM Test succeeded. Press escape within 4 seconds to enter boot interface. 1) Start system. 2) Recover password. 3) Enter command shell. Option? 3 Password: > > > help Valid commands are: auto Boot per boot environment variable settings boot Boot specified image date Display or set the system date and time debug Hardware debug - General debug utilities diag Hardware tests - Hardware test diagnostics help Display this list of commands helpenv Display help for boot environment variables hinv Display hardware inventory passwd Set the boot modification password ping Ping test printenv Display all boot environment variables reset Reset the system resetpw Remove the boot modification password setenv Set a boot environment variable saveenv Save the current boot environment variables unsetenv Unset a boot environment variable version Display boot version info > > printenv AutoLoad=yes ENET_MAC=00051E05266C InitTest=MEM() LoadIdentifiers=Fabric Operating System;Fabric Operating System OSLoadOptions=quiet;quiet OSLoader=ATA()0x62a38;ATA()0x29498 OSRootPartition=hda2;hda1 SkipWatchdog=yes > > boot ATA()0x62a38 -s Booting "Manually selected OS" image. Entry point at 0x01000000 ... Linux/PPC load: BootROM command line: -s Uncompressing Linux...done. Now booting the kernel Linux version 2.4.19 (swrel@blackcomb) (gcc version 2.95.3 20010112 (prerelease)) #1 Mon Feb 13 00:16:40 PST 2006 cpld_init: platform (34) not supported Brocade Silkworm port (C) 2002 MontaVista Software, Inc. (source@mvista.com) On node 0 totalpages: 32768 zone(0): 4096 pages. zone (0): min(32), low(160), high (256) zone(1): 28672 pages. zone (1): min(224), low(1120), high (1792) zone(2): 0 pages. Kernel command line: -s Set up jiffies counter to wrap in 0 seconds. Calibrating FIT timer... running at 2544 Hz. [TSR_FP=1] Calibrating delay loop... 499.71 BogoMIPS Memory: 123840k available (1780k kernel code, 1100k data, 72k init, 0k highmem) Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) Inode cache hash table entries: 8192 (order: 4, 65536 bytes) Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) Page-cache hash table entries: 32768 (order: 5, 131072 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware PCI: moved device 00:02.0 resource 2 (101) to 1000 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded SGI XFS with no debug enabled i2c-core.o: i2c core module version 2.6.3 (20020322) i2c-dev.o: i2c /dev entries driver module version 2.6.3 (20020322) i2c-proc.o version 2.6.3 (20020322) pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xfdfea300 (irq = 1) is a 16550A ttyS01 at 0xfdfe9200 (irq = 0) is a 16550A PPC 405 watchdog driver v0.5. (Timer driven) IBM gpio driver version 07.25.02 GPIO #0 at 0xc9000700 SWBD Platform Driver v1.0: [type 34, rev 1]. Config Silkworm Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 read cpld_data 0x90 Silkworm CE-2 CPLD ATA interface configured [CPLD version 16] cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0487f08 hda: SILICONSYSTEMS INC 256MB-3620, ATA DISK drive ide0 at 0xcb0151f0-0xcb0151f7,0xcb0153f6 on irq 28 hda: 508928 sectors (261 MB) w/0KiB Cache, CHS=994/16/32 Partition check: hda: hda1 hda2 RAMDISK driver initialized: 16 RAM disks of 50000K size 1024 blocksize loop: loaded (max 8 devices) eth0: ZMII bridge in RMII mode eth0: Phy @ 0x1, type BCM5221 (0x004061e4) eth0: IBM OCP 10/100 Mbps ethernet: EMAC0, MAC 00:05:1e:05:26:6c eth0: Tx/Rx Interrupt mitigation (1500 pps) eth1: ZMII bridge in RMII mode eth1: Read error on PHY 0x02, register 2 eth1: PHY 0x02 not found ATA polled-mode panic dumper on char-major-252. silkworm: Using SWBD34 flash configuration Creating 6 MTD partitions on "Boot flash": 0x00000000-0x00020000 : "bootenv0: boot environment (1)" 0x00020000-0x00040000 : "bootenv1: boot environment (2)" 0x00040000-0x00200000 : "prom0: boot prom (1)" 0x00200000-0x003c0000 : "prom1: boot prom (2)" 0x003c0000-0x003e0000 : "unused" 0x003e0000-0x00400000 : "bootsel: boot prom selector" mtdchar: write-caching enabled iic0: IBM on-chip iic adapter module 2003.15.08 iic1: IBM on-chip iic adapter module 2003.15.08 M41T11 Real-time-clock Driver v1.1 m41t11: Called to probe for bus IIC-0 m41t11: I2C Real-Time-Clock detected on iic0 addr 0x68 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 8192 bind 8192) Linux IP multicast router 0.06 plus PIM-SM ip_tables: (C) 2000-2002 Netfilter core team NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. RAMDISK: ext2 filesystem found at block 0 RAMDISK: Loading 2603 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-done. Freeing initrd memory: 2603k freed VFS: Mounted root (ext2 filesystem). Attempting to find a root file system on hda2... kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... okay Freeing unused kernel memory: 72k init INIT: version 2.78 booting sh-2.04# sh-2.04# mount -o remount,rw,noatime / EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,2), internal journal sh-2.04# sh-2.04# mount /dev/hda2 /mnt sh-2.04# sh-2.04# /sbin/passwddefault modprobe: modprobe: Can't locate module char-major-244 modprobe: modprobe: Can't locate module char-major-245 passwdCfg: fabosInit failed with 2 All account passwords have been successfully set to factory default. sh-2.04# sh-2.04# reboot -f flushing ide devices: hda Restarting system.