U-Boot 1.1.3 (May 8 2013 - 21:16:08) Board: Ralink APSoC DRAM: 16 MB relocate_code Pointer at: 80fb4000 ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 42 spi device id: 1c 70 16 1c 70 (70161c70) Warning: un-recognized chip ID, please update bootloader! raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 4.0.1.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 128 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 16 MBytes Flash component: SPI Flash Date:May 8 2013 Time:21:16:08 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =16 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 4 3 2 1 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 . Image Name: MIPS OpenWrt Linux-4.14.54 Created: 2018-07-30 16:25:17 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1369074 Bytes = 1.3 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:14e3f2 ..................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 16 Starting kernel ... [ 0.000000] Linux version 4.14.54 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9)) #0 Mon Jul 30 16:25:17 2018 [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is Planex MZK-DP150N [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 01000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] random: get_random_bytes called from 0x803ee72c with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping off. Total pages: 4064 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes) [ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Writing ErrCtl register=00051190 [ 0.000000] Readback ErrCtl register=00051190 [ 0.000000] Memory: 11716K/16384K available (3417K kernel code, 175K rwdata, 424K rodata, 200K init, 210K bss, 4668K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 360MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns [ 0.000016] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns [ 0.015713] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080) [ 0.098013] pid_max: default: 32768 minimum: 301 [ 0.107610] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.120727] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.143581] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.163140] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.175396] pinctrl core: initialized pinctrl subsystem [ 0.188469] NET: Registered protocol family 16 [ 0.206692] Can't analyze schedule() prologue at 80352170 [ 0.256429] rt2880_gpio 10000600.gpio: registering 22 gpios [ 0.267571] rt2880_gpio 10000600.gpio: registering 22 irq handlers [ 0.280607] rt2880_gpio 10000660.gpio: registering 6 gpios [ 0.291567] rt2880_gpio 10000660.gpio: registering 6 irq handlers [ 0.313804] clocksource: Switched to clocksource MIPS [ 0.326074] NET: Registered protocol family 2 [ 0.336640] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.350539] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.363124] TCP: Hash tables configured (established 1024 bind 1024) [ 0.376113] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.387760] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.400698] NET: Registered protocol family 1 [ 0.415474] rt-timer 10000100.timer: maximum frequency is 3662Hz [ 0.429078] Crashlog allocated RAM at address 0xf00000 [ 0.443529] workingset: timestamp_bits=30 max_order=12 bucket_order=0 [ 0.467090] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.478681] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.523295] io scheduler noop registered [ 0.531073] io scheduler deadline registered (default) [ 0.542956] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.561593] console [ttyS0] disabled [ 0.568775] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.588488] console [ttyS0] enabled [ 0.588488] console [ttyS0] enabled [ 0.602272] bootconsole [early0] disabled [ 0.602272] bootconsole [early0] disabled [ 0.619172] cacheinfo: Failed to find cpu0 device node [ 0.629543] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.658874] spi spi0.0: force spi mode3 [ 0.667988] m25p80 spi0.0: unrecognized JEDEC id bytes: 1c, 70, 16 [ 0.680495] m25p80: probe of spi0.0 failed with error -2 [ 0.692097] libphy: Fixed MDIO Bus: probed [ 0.706685] rt3050-esw 10110000.esw: link changed 0x00 [ 0.718657] mtk_soc_eth 10100000.ethernet: generated random MAC address 7a:8d:df:24:50:4a [ 0.736305] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.754100] rt2880_wdt 10000120.watchdog: Initialized [ 0.766903] NET: Registered protocol family 10 [ 0.785248] Segment Routing with IPv6 [ 0.792792] NET: Registered protocol family 17 [ 0.801932] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.827865] 8021q: 802.1Q VLAN Support v1.8 [ 0.841729] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 0.856784] Please append a correct "root=" boot option; here are the available partitions: [ 0.873476] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 0.891228] Rebooting in 1 seconds.. U-Boot 1.1.3 (May 8 2013 - 21:16:08) Board: Ralink APSoC DRAM: 16 MB relocate_code Pointer at: 80fb4000 ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 42 spi device id: 1c 70 16 1c 70 (70161c70) Warning: un-recognized chip ID, please update bootloader! raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 4.0.1.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 128 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 16 MBytes Flash component: SPI Flash Date:May 8 2013 Time:21:16:08 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =16 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 4 3 2 1 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 . Image Name: MIPS OpenWrt Linux-4.14.54 Created: 2018-07-30 16:25:17 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1369074 Bytes = 1.3 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:14e3f2 ..................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 16 Starting kernel ... [ 0.000000] Linux version 4.14.54 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9)) #0 Mon Jul 30 16:25:17 2018